Zaawansowana metoda symulacyjna zwiększenia efektywności obróbki stopu niklu - studium przypadku

• Autorzy: Wojciech Zębala , Andrzej Matras , Tadeusz Otko

Warianty tytułu

Advanced Simulation Method of Efficiency Increase When Nickel Alloy Machining - Case Study

• Języki publikacji: PL

Abstrakty

Artykuł przedstawia badania symulacyjne toczenia powierzchni części lotniczej. Przeprowadzono analizę kształtu i wymiarów obrabianej powierzchni bloku silnika o cylindrycznym kształcie i grubości ścianki ok. 10 mm.(fragment tekstu)

EN

Paper presents some investigations concerning FEM simulation analysis and optimization of turning process of the external engine Block surface. As a part of examinations carried out, selected cutting operations of upper flange were analyzed. These concerned facing, external and internal turning. To conduct the feed speed optimization process a force model was built which enabled to calculate cutting forces values depending on cutting parameters and cross section of machined layer. The optimization research had the aim to stabilize the time course of cutting force values taking place during machining.(original abstract)

Słowa kluczowe

PL

Przedsiębiorstwo; Produkcja; Zarządzanie produkcją; Technologia; Optymalizacja

EN

Enterprises; Production; Production management; Technology; Optimalization

• Czasopismo: Zarządzanie Przedsiębiorstwem / Polskie Towarzystwo Zarządzania Produkcją
• Rocznik: 2017
• Numer: nr 2
• Strony: 34--40

Twórcy

autor

Wojciech Zębala

• Politechnika Krakowska

autor

Andrzej Matras

• Politechnika Krakowska

autor

Tadeusz Otko

• Politechnika Krakowska

Bibliografia

• Choudhary S.K., Appa Rao I.V.K., Optimization of cutting parameters for maximizing tool life. "International Journal of Machine Tools and Manufacture" 39/1999, pp. 343-353.
• Dudzinski D., Devillez A., Moufki A., Larrouque're D., Zerrouki V., Vigneau J. ,A review of developments towards dry and high speed machining of Inconel 718 alloy "International Journal of Machine Tools & Manufacture" 44/2004, pp 439-456.
• Eckstein M., Mankova I., Vrabel M., Beno J., Comparison of Sensors Signal Quality when Drilling Inconel 718 "Procedia CIRP" 33/2015, pp. 227-232.
• Jakubowski J., Peterka J., Design for manufacturability in virtual environment using knowledge engineering. "Management and Production Engineering Review" 5/1/2014, pp. 3-10.
• Radkowski G., Sęp J., Surface quality of a milled gamma titanium aluminide for aeronautical applications. "Management and Production Engineering Review" 5/2/ 2014, pp. 60-65.
• Singaravel B., Selvaraj T., Experimental investigation on cutting forces, specific cutting pressure, co-efficient of friction and shear energy in turning of HSLA steel. "Management and Production Engineering Review" 7/1/2016, pp. 71-76.
• Ulutan D., Ozel T., Machining induced surface integrity in titanium and nickel alloys: A review. "International Journal ofMachine Tools &Manufacture" 51/2011, pp. 250-280.
• User's Manual of Production Module v7. 1 machining simulation software, Minneapolis, MN, 2015.
• Varga G., Possibility to increase the life time of surfaces on parts by the use of diamond burnishing process. "Key Engineering Materials" 686/2016, p. 100.
• Vaz Jr. M., Owen D.R.J., Kalhori V., Lundblad M., Lindgren L.-E., Modelling and Simulation of Machining Processe, "Archives of Computational Methods in Engineering" 14/2/2007, pp. 173-204.
• Zębala W., Milling optimization of difficult to machine alloys. "Management and Production Engineering Review" 1/1/2010, pp. 59-70.